whalerat97

Door Handle Replacement It's worth replacing door handles if you don't like the way they look or if they're difficult to use. Installing a new door handle is easy if you have patience. Modern door handles are typically equipped with cover plates that conceal the screws, giving them a more attractive appearance. However, you'll need to attach them separately if the new handle does not already have them. Remove the old Handle Door handles are not only an important aesthetic addition to your home, but they're also vital for safety since they let you lock and unlock your door. But, over time the door handle could lose its grip, appear loose or start to look old and worn out. www.repairmywindowsanddoors.co.uk is an indication that it's time for a replacement. One of the first indications that your door handle needs replacing is when it becomes difficult to operate. This is a serious problem because you won't be in a position to lock or unlock the door and put you and your family at risk. It is also a good idea to replace the handle on your door when it's damaged or broken. A broken door handle can be quite dangerous, especially in the event that your children or senior family members have difficulty opening it, and get trapped in the. It's easy to replace a broken handle on a door. Most modern door handles are a standard size, so they will fit on any door. If you're unsure if the new door handle you're buying will fit, try removing the old one and measuring the holes in its housing. This will help you to buy the correct sized door handle. It is the easiest way to remove the old door handle by unscrewing it from the door. This is typically done with a screw driver. However, some door handles have the cover plate which hides the mounting screws so you'll need to pry off this to reach the screws underneath. After you have removed the old handle, take note of the way in which the spindle is connected. This will assist you in aligning the new handle. You can also remove the door handle by unscrewing the latch mechanism. This is typically done with a screwdriver but you'll need to find the small latch, which should be at the edge of the trim piece. Once you've removed the latch, you'll need to remove the handle from the strike plate and then the latch away from the door's edge. Remove the Strike Plate You'll need to replace your latch plate after replacing the handle. It's the part that holds the hole where the door's latch hooks in when the door is closed. The new handles will have two latch plates which are a circular and a rectangular plate (see the diagram above which shows the various parts of a door handle). If you have an old rectangular latch plate, you can replace it with a round one. This will let the latch hook into the strike plate, making the handle easier. The first step is to take off the screw holding the old latch plate. These screws can be quite tight and will require some force to loosen. It might be beneficial to have a second person assist with this part if possible. The latch plate should easily come out of the door after the screws have been removed. If it's stuck or won't move, use a small nail file to scrape around the edges of the latch plate. This can help loosen the plate. Now you can move on to preparing the new door strike plate for installation. Screw the latch plate into the door jamb using the screws that were included with the new handles. Don't over tighten your screws because this could damage the strike plate. If you're not sure if the latch plate is in the right position You can try closing and then opening the door to check if it closes and latches correctly. If not then you'll have to adjust the strike plate up or down, or even forward or back until the door closes and latches correctly. If the door is moving or jiggling, then it may be necessary to expand the hole for latching in the strike plate. This is more frequent in older doors, however it could be due to wear and tear hinge mortises that are too shallow or are not sized correctly for the latch, or from damage or a broken strike plate. If this is the situation, follow the same procedure to adjust the strike plate, but using the use of a metal file instead an hammer and chisel. Eliminating the Latch The latch is a curved metal piece which slides in and out of a hole on the inside of your door. When you turn the handle, it pushes the latch forward, allowing you to open the door. It also connects to an opening in the door frame to keep the door closed. If your door is wobbling when you close, an upgrade to the latch could be all you need to correct the issue. It's difficult to see the screws that attach the latch to the door, but there's usually a small hole on the trim plate that allows you to insert a screwdriver and take it off. After you've removed the trim plate, it'll be easy to remove the latch and the remaining bolts that hold the spindle and latch in place. If the latch isn't easily removed then use a paperclip tool to take it off the handle mechanism. Insert the item in the recessed latch slot, and gently twist it or jiggle until you feel that the latch and handle are beginning to separate. It may take this several times before the latch comes loose enough to allow it to be pulled out. It should be possible to slide the new latch into its slot with no problems after you have removed the old one. Use your new screws to connect the latch to the strike plate or door frame. Make sure that it is correctly positioned in the slot, and aligned with the screw chambers. Before you install the new handle, make sure to measure your existing backset (the distance from the center of the big hole on the front of the door to the edge). Also, ensure whether the size of the latch on the new handle is in line with the measurement of your existing handle. You'll require a new cylinder for your lock if you're replacing the latch and handle or if your current one is damaged. If you're not changing locks the new latch will fit into your existing recess and will work just fine with the keys you have currently. Make sure you select a latch with a rectangular cover plate that match your handles. Removal of the Cover Plate You can replace your door handles with a modern rose and lever designs to improve the look of your house. You can purchase complete sets with matching escutcheons, privacy adaptors and escutcheons. To replace an internal door handle remove the cover plate (or rose), which covers the screws and mechanism. Find an opening tab on the plate, and employ a flathead screwdriver lift it off the knob. It may have a slot along one edge or be held in place by pins. Remove the screw that holds the handle in the interior and put it aside after the cover plate has been removed. It is also necessary to remove the screws that hold the latch and inner plates and the latch plate, which can be done by loosening them with the help of a Philips screwdriver. Take the inner plates and latch from the door. Put them away. Most doors have gaps between the jamb of the door and the edge of the frame that makes room for a handle, however not all do. If it doesn't then you'll have to drill a hole into the door for the new handle. The process for doing this is similar to the procedure for opening a door with the lock, however you'll be taking extra care not to damage the door or frame. After drilling the holes after which you'll have to put in new screws for the door knob. Make sure to buy the same size as the previous ones, so you do not end up with a handle that's too tight or loose. Installing a new latch and strike rod is also mandatory. These aren't included in all door handle sets. If you're in search of a reliable replacement for your interior door handle set, try the Amazon's Choice FAERSI two-piece chrome-finished handle set. It is a factory-fit and has received hundreds of 5-star reviews. It's a great option to replace damaged or worn interior door handle hardware on your Chevy HHR.